I want to know about...

THE CITY RECORD

184

Districts, where authorized by the City Planning Commission, both to protect residences from an undesirable environment and to ensure the reservation of adequate areas for industrial development; and d dwelling units in M1-6D Districts.
41-12
M2 Medium Manufacturing Districts Medium Performance UPDATING TO REFLECT NEW M2A DISTRICTS AND EXISTING
ALLOWANCES IN OTHER DISTRICTS
These districts are designed for manufacturing and related activities which can meet a medium level of performance standards. Enclosure of such activities is not normally required except in areas along the boundary of a Residence District. No new residences or community facilities are permitted.
41-13
M3 Heavy Manufacturing Districts Low Performance These districts are designed to accommodate the essential heavy industrial uses which involve more objectionable influences and hazards, and which, therefore, cannot reasonably be expected to conform to those performance standards which are appropriate for most other types of industrial development. No new residences or community facilities are permitted.

ARTICLE IV
MANUFACTURING DISTRICT REGULATIONS
Chapter 2
Use Regulations 42-00
GENERAL PROVISIONS
THE LANGUAGE IN THIS SECTION REFLECTS THE PROPOSED
MODIFICATIONS IN CITY OF YES FOR ECONOMIC
OPPORTUNITY, A PARRALLEL TEXT AMENDMENT
In order to carry out the purposes and provisions of this Resolution, the uses within buildings or other structures as well as the open uses of zoning lots, or portions thereof, have been classified and combined into ten separate Use Groups with similar characteristics.
Use Groups 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10, are permitted in Manufacturing Districts subject to the provisions of the following Sections:
a Sections 42-11 through 42-20 establish general use allowances in Use Groups 1 through 10, including each use listed separately therein, by Manufacturing District, and additional provisions for certain uses where applicable.
b Section 42-30 SPECIAL PROVISIONS APPLICABLE TO
CERTAIN DISTRICTS sets forth special provisions applicable to the following Manufacturing Districts:
1 M1-1D, M1-2D, M1-3D, M1-4D and M1-5D Districts, as set forth in Section 42- 31 Residential uses in M1-1D through M1-5D Districts;
2 M1-6D Districts, as set forth in Section 42-32 Use regulations in M1-6D Districts;
3 M1-5M and M1-6M Districts, as set forth in Section 42-33
Use regulations in M1-5M and M1-6M Districts;
4 M1-1, M1-5 and M1-6 Districts in certain areas, as set forth in Section 42-34 Use regulations in certain M1-1, M1-5 and M1-6 Districts; and 5 M1-5B Districts, as set forth in Section 42-35 Use regulations in M1-5B Districts. ; and 6 Manufacturing Districts with an A suffix, as set forth in Section 42-36 Use regulations in A suffix districts.

42-36
Use Regulations in Manufacturing Districts with an A Suffix
THURSDAY, JANUARY 11, 2024

listed in Use Group 8 shall be permitted;
3 all community facility uses without sleeping accommodations listed in Use Group 3B shall be permitted.
b In M2 Districts with an A suffix, the use regulations for an M1
District with an A suffix shall apply, inclusive of performance standards, supplementary use regulations, and sign regulations.

ARTICLE IV
MANUFACTURING DISTRICT REGULATIONS
Chapter 3
Bulk Regulations 43-00
APPLICABILITY AND GENERAL PROVISIONS

43-10
FLOOR AREA REGULATIONS

43-12
Maximum Floor Area Ratio M1 M2 M3
In all districts, as indicated, for any zoning lot, the maximum floor area ratio shall not exceed the floor area ratio set forth in the following table, except as otherwise provided in the following Sections:
Section 43-121

Expansion of existing manufacturing buildings
Section 43-122

Maximum floor area ratio for community facilities
Section 43-13

Floor Area Bonus for Public Plazas Floor Area in Manufacturing Districts With an A Suffix
Section 43-14

Floor Area Bonus for Public Plazas and Arcades
Section 43-15

Existing Public Amenities for which Floor Area Bonuses Have Been Received
Section 43-16

Special Provisions for Zoning Lots Divided by District Boundaries
Section 43-61

Bulk Regulations for Residential Uses in M1-1D
Through M1-5D Districts
Section 43-62

Bulk Regulations in M1-6D Districts

43-13
Floor Area Bonus for Public Plazas Floor Area in Manufacturing Districts With an A Suffix M1-6
MOVING EXISTING TEXT TO SECTION 43-14
In the district indicated, except for M1-6D Districts, for each square foot of public plaza provided on a zoning lot, in accordance with the provisions of Section 37-70, inclusive, the total floor area permitted on that zoning lot under the provisions of Section 43-12
Maximum Floor Area Ratio may be increased by six square feet.
NEW PROVISIONS, PER PROPOSAL
43-131
Definitions Definitions specifically applicable to this Chapter are set forth in this Section. The definitions of other defined terms are set forth in Section 12-10 DEFINITIONS, except where explicitly stated otherwise in individual provisions in this Chapter.
Qualifying uses
42-361
General use modifications
Qualifying uses shall include certain commercial and manufacturing uses eligible for higher permitted floor area ratio in M2 and M3 Districts with an A suffix.

In M1 and M2 Districts with an A suffix, the applicable use regulations shall be modified as follows:

In M2 Districts with an A suffix such uses shall include referenced commercial and manufacturing uses.

a In M1 Districts with an A suffix:

In M3 Districts with an A suffix, such uses shall include qualifying uses in M2 Districts with an A suffix, as well as the following;

1 all retail and service uses listed in Use Group 6 shall be permitted, and no associated size limitations shall apply;
2 all recreation, entertainment and assembly space uses
From Use Group 4B and 4C
utility infrastructure uses