Voglio sapere a riguardo di…

16490

Federal Register / Vol. 86, No. 58 / Monday, March 29, 2021 / Rules and Regulations
military use for purposes of determining controls under paragraph .a. entails a structural, electrical or mechanical feature involving one or more components that are specially designed for military use. Such components include:
a. Pneumatic tire casings of a kind specially designed to be bullet-proof;
b. Armored protection of vital parts e.g., fuel tanks or vehicle cabs;
c. Special reinforcements or mountings for weapons;
d. Black-out lighting.
b. Other ground vehicles, parts and components, as follows:
b.1. Unarmed vehicles that are derived from civilian vehicles and that have all of the following:
b.1.a. Manufactured or fitted with materials or components other than reactive or electromagnetic armor to provide ballistic protection equal to or better than level III
National Institute of Justice standard 0108.01, September 1985 or equivalent standards;
b.1.b. A transmission to provide drive to both front and rear wheels simultaneously, including those for vehicles having additional wheels for load bearing purposes whether driven or not;
b.1.c. Gross vehicle weight rating GVWR
greater than 4,500 kg; and b.1.d. Designed or modified for off-road use.
b.2. Parts and components having all of the following:
b.2.a. Specially designed for vehicles specified in paragraph .b.1 of this entry; and b.2.b. Providing ballistic protection equal to or better than level III National Institute of Justice standard 0108.01, September 1985
or equivalent standards.
Note 1 to paragraph b: Ground vehicles otherwise controlled by 0A606.b.1 that contain reactive or electromagnetic armor are subject to the controls of USML Category VII.
Note 2 to paragraph b: ECCN 0A606.b.1
does not control civilian vehicles specially designed for transporting money or valuables.
Note 3 to paragraph b: Unarmed means not having installed weapons, installed mountings for weapons, or special reinforcements for mounts for weapons.
c. Air-cooled diesel engines and engine blocks for armored vehicles that weigh more than 40 tons.
d. Fully automatic continuously variable transmissions for tracked combat vehicles.
e. Deep water fording kits specially designed for ground vehicles controlled by ECCN 0A606.a or USML Category VII.
f. Self-launching bridge components not enumerated in USML Category VIIg specially designed for deployment by ground vehicles enumerated in USML
Category VII or this ECCN.
g. through w. Reserved x. Parts, components, accessories, and attachments that are specially designed for a commodity enumerated or otherwise described in ECCN 0A606 other than 0A606.b or 0A606.y or a defense article enumerated in USML Category VII and not
VerDate Sep<11>2014

18:05 Mar 26, 2021

Jkt 253001

elsewhere specified on the USML or in 0A606.y.
Note 1: Forgings, castings, and other unfinished products, such as extrusions and machined bodies, that have reached a stage in manufacture where they are clearly identifiable by mechanical properties, material composition, geometry, or function as commodities controlled by ECCN 0A606.x are controlled by ECCN 0A606.x.
Note 2: Parts, components, accessories and attachments enumerated in USML paragraph VIIg are subject to the controls of that paragraph.
Parts, components, accessories and attachments described in ECCN 0A606.y are subject to the controls of that paragraph.
y. Specific parts, components, accessories, and attachments specially designed for a commodity enumerated or otherwise described in this ECCN other than ECCN 0A606.b or for a defense article in USML Category VII and not elsewhere specified on the USML or the CCL, as follows, and parts, components, accessories, and attachments specially designed therefor:
y.1. Brake discs, rotors, drums, calipers, cylinders, pads, shoes, lines, hoses, vacuum boosters, and parts therefor;
y.2. Alternators and generators;
y.3. Axles;
y.4. Batteries;
y.5. Bearings e.g., ball, roller, wheel;
y.6. Cables, cable assembles, and connectors;
y.7. Cooling system hoses;
y.8. Hydraulic, fuel, oil, and air filters, not controlled by ECCN 1A004;
y.9. Gaskets and o-rings;
y.10. Hydraulic system hoses, fittings, couplings, adapters, and valves;
y.11. Latches and hinges;
y.12. Lighting systems, fuses, and components;
y.13. Pneumatic hoses, fittings, adapters, couplings, and valves;
y.14. Seats, seat assemblies, seat supports, and harnesses;
y.15 Tires, except run flat; and y.16 Windows, except those for armored vehicles.

16. In supplement no. 1 to part 774
the CCL, Category 1, ECCN 1A002 is revised to read as follow:

1A002 Composite structures or laminates, as follows see List of Items Controlled.
License Requirements Reason for Control: NS, NP, AT
Controls NS applies to entire entry.
NP applies to 1A002.b.1 in the form of tubes with an inside diameter between 75 mm and 400 mm.

PO 00000

Frm 00010

Fmt 4701

Country Chart See Supp. No. 1 to part 738
NS Column 2
NP Column 1

Controls AT applies to entire entry.

Country Chart See Supp. No. 1 to part 738
AT Column 1

Reporting Requirements See 743.1 of the EAR for reporting requirements for exports under License Exceptions, and Validated End-User authorizations.
List Based License Exceptions See Part 740
for a Description of All License Exceptions LVS: $1,500; N/A for NP; N/A for composite structures or laminates controlled by 1A002.a, having an organic matrix and made from materials controlled by 1C010.c or 1C010.d.
GBS: N/A
Special Conditions for STA
STA: License Exception STA may not be used to ship any item in this entry to any of the destinations listed in Country Group A:6 See Supplement No. 1 to part 740 of the EAR.
List of Items Controlled Related Controls: 1 See ECCNs 1E001
development and production and 1E201 use for technology for items controlled by this entry. 2 Also see ECCNs 1A202, 1C010, 1C210, 9A010, and 9A110. 3 Composite structures specially designed for missile applications including specially designed subsystems, parts, and components are controlled by ECCN
9A110. 4 Composite structures or laminates specially designed or prepared for use in separating uranium isotopes are subject to the export licensing authority of the Nuclear Regulatory Commission see 10
CFR part 110.
Related Definitions: N/A
Items:
a. Made from any of the following:
a.1. An organic matrix and fibrous or filamentary materials specified by 1C010.c or 1C010.d; or a.2. Prepregs or preforms specified by 1C010.e;
b. Made from a metal or carbon matrix, and any of the following:
b.1. Carbon fibrous or filamentary materials having all of the following:
b.1.a. A specific modulus exceeding 10.15 x 106 m; and b.1.b. A specific tensile strength exceeding 17.7 x 104 m; or b.2. Materials controlled by 1C010.c.
Note 1: 1A002 does not control composite structures or laminates made from epoxy resin impregnated carbon fibrous or filamentary materials, for the repair of civil aircraft structures or laminates, having all of the following:
a. An area not exceeding 1 m2;
b. A length not exceeding 2.5 m; and c. A width exceeding 15 mm.
Note 2: 1A002 does not control semifinished items, specially designed for civilian applications as follows:
a. Sporting goods;

Sfmt 4700

E:FRFM29MRR3.SGM

29MRR3