Je veux savoir à propos de…

Federal Register / Vol. 86, No. 150 / Monday, August 9, 2021 / Notices square inch i.e., W1.4 or D1.4 is .014 square inches.
Smooth wire is wire that has a uniform cross-sectional diameter throughout the length of the wire.
Deformed wire is wire with indentations or raised transverse ribs, which results in wire that does not have a uniform cross-sectional diameter throughout the length of the wire.
Rolls of subject wire mesh are produced in the following styles and nominal width and length combinations:
Style: 6X6 W1.4/W1.4 or D1.4/D1.4 i.e., 10
gauge Roll Sizes:
5 X 50
5 X 150
6 X 150
5 X 200
7 X 200
7.5 X 200
Style: 6X6 W2.1/W2.1 or D2.1/D2.1 i.e., 8
gauge Roll Sizes:
5 X 150
Style: 6X6 W2.9/W2.9 or D2.9/D2.9 i.e., 6
gauge Roll Sizes:
5 X 150
7 X 200
All rolled wire mesh is included in scope regardless of length.
Sheets of subject wire mesh are produced in the following styles and nominal width and length combinations:
Style: 6X6 W1.4/W1.4 or D1.4/D1.4 i.e., 10
gauge
Sheet Size:
36 X 7
4 X 7
4 X 76
5 X 10
7 X 20
76 X 20
8 X 126
8 X 15
8 X 20
Style: 6X6 W2.1/W2.1 or D2.1/D2.1 i.e., 8
gauge Sheet Size:
5 X 10
7 X 20
76 X 20
8 X 126
8 X 15
8 X 20
Style: 6X6 W2.9/W2.9 or D2.9/D2.9 i.e., 6
gauge Sheet Size:
36 X 20
5 X 10
7 X 20
76 X 20
8 X 126
8 X 15
8 X 20
Style: 6X12 W4/W4 or D4/D4 i.e., 4 gauge Sheet Size:
8 X 20
Style: 4X4 W2.9/W2.9 or D2.9/D2.9 i.e., 6
gauge Sheet Size:
5 X 10
7 X 20

lotter on DSK11XQN23PROD with NOTICES1

1.4
2.1
2.9
4.0

i.e., i.e., i.e., i.e.,
10 gauge
8 gauge
6 gauge
4 gauge

To the extent a roll or sheet of welded wire mesh falls within the permissible variations provided above, it is within this scope.
In addition to the tolerances permitted in ASTM specification A1064/A1064M, wire mesh within this scope includes combinations where:
1. A width and/or length combination varies by one grid size in any direction, i.e., 6 inches in length or width where the wire meshs grid size is 6X6; and/or 2. The center-to-center spacing between individual wires may vary by up to one quarter of an inch from the nominal grid size specified.
Length is measured from the ends of any wire and width is measured between the center-line of end longitudinal wires.
Additionally, although the subject wire mesh typically meets ASTM A1064/A1064M, the failure to include certifications, test reports or other documentation establishing that the product meets this specification does not remove the product from the scope. Wire mesh made to comparable foreign specifications e.g., DIN, JIS, etc. or proprietary specifications is included in the scope.

VerDate Sep<11>2014

17:26 Aug 06, 2021

Jkt 253001

76 X 20
8 X 126
8 X 128
8 X 15
8 X 20
Style: 4X4 W4/W4 or D4/D4 i.e., 4 gauge Sheet Size:
5 X 10
8 X 126
8 X 128
8 X 15
8 X 20
Any product imported, sold, or invoiced in one of these size combinations is within the scope.
ASTM specification A1064/A1064M
provides for permissible variations in wire gauges, the spacing between transverse and longitudinal wires, and the length and width combinations. To the extent a roll or sheet of welded wire mesh falls within these permissible variations, it is within this scope.
ASTM specification A1064/A1064M also defines permissible oversteeling, which is the use of a heavier gauge wire with a larger cross-sectional area than nominally specified.
It also permits a wire diameter tolerance of 0.003 inches for products up to W5/D5 and 0.004 for sizes over W5/D5. A producer may oversteel by increasing smooth or deformed wire diameter up to two whole number size increments on Table 1 of A1064.
Subject wire mesh has the following actual wire diameter ranges, which account for both oversteeling and diameter tolerance:

Maximum oversteeling No.

W/D No.

3.4
4.1
4.9
6.0

Diameter range inch 0.093
0.161
0.189
0.223

to to to to
0.211.
0.231.
0.253.
0.280.

Excluded from the scope is wire mesh that is galvanized i.e., coated with zinc or coated with an epoxy coating. In order to be excluded as galvanized, the excluded welded wire mesh must have a zinc coating thickness meeting the requirements of ASTM
specification A641/A641M. Epoxy coating is a mix of epoxy resin and hardener that can be applied to the surface of steel wire.
Merchandise subject to this investigation are classified under Harmonized Tariff Schedule of the United States HTSUS
categories 7314.20.0000 and 7314.39.0000.
While HTSUS subheadings are provided for convenience and customs purposes, the written description of the scope of this investigation is dispositive.

DEPARTMENT OF COMMERCE

FR Doc. 202116982 Filed 8621; 8:45 am
SUMMARY:

BILLING CODE 3510DSP

PO 00000

Frm 00010

Fmt 4703

43527

Sfmt 4703

National Oceanic and Atmospheric Administration RTID 0648XB293

Atlantic Highly Migratory Species;
Meeting of the Atlantic Highly Migratory Species Advisory Panel National Marine Fisheries Service NMFS, National Oceanic and Atmospheric Administration NOAA, Commerce.
ACTION: Notice of public webinars/
conference calls.
AGENCY:

NMFS will hold a 3-day Atlantic Highly Migratory Species HMS Advisory Panel AP meeting in September 2021. The intent of the HMS
AP meeting is to consider options for the conservation and management of Atlantic HMS. The meeting is open to the public.

E:FRFM09AUN1.SGM

09AUN1