Federal Register - February 24, 2021
Version en texte Qu'est-ce que c'est?Dateas est un site Web indépendant, non affilié à un organisme gouvernemental. La source des documents PDF que nous publions est l'agence officielle indiquée dans chacun d'eux. Les versions en texte sont des transcriptions non officielles que nous faisons pour fournir de meilleurs outils d'accès et de recherche d'informations, mais peuvent contenir des erreurs ou peuvent ne pas être complètes.
Source: Federal Register
i Retained Initial Compliance Time: OneTime Initial Threshold, With No Changes This paragraph restates the requirements of paragraph i of AD 20191304, with no
j Retained Restrictions on Alternative Actions and Intervals With a New Exception This paragraph restates the requirements of paragraph j of AD 20191304, with a new exception. Except as required by paragraph k of this AD, after the existing maintenance or inspection program has been revised as required by paragraph g of this AD, no alternative actions e.g., inspections and intervals may be used unless the actions and intervals are approved as an alternative method of compliance AMOC in accordance with the procedures specified in paragraph n1 of this AD.
khammond on DSKJM1Z7X2PROD with RULES
k New Maintenance or Inspection Program Revision Except as specified in paragraph l of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency EASA AD 20200173, dated August 5, 2020 EASA AD 20200173.
Accomplishing the maintenance or inspection program revision required by this paragraph terminates the requirements of paragraph g of this AD.
l Exceptions to EASA AD 20200173
1 Where EASA AD 20200173 refers to its effective date, this AD requires using the effective date of this AD.
2 The requirements specified in paragraphs 1 and 3 of EASA AD 2020
0173 do not apply to this AD.
3 Paragraph 4 of EASA AD 20200173
specifies revising the approved AMP
within 12 months after its effective date, but this AD requires revising the existing maintenance or inspection program, as
VerDate Sep<11>2014
16:14 Feb 23, 2021
Jkt 253001
11105
changes. For airplanes with an original airworthiness certificate or original export certificate of airworthiness issued on or before January 30, 2018: For CMR task 2200005, a one-time initial threshold, as
specified in ATR ATR72 Time Limits Document, Revision 16, dated January 30, 2018, is allowed as specified in figure 2 to paragraph i of this AD.
applicable, to incorporate the limitations, tasks and associated thresholds and intervals specified in paragraph 4 of EASA
AD 20200173 within 90 days after the effective date of this AD.
4 Except as provided by paragraph 2 of EASA AD 20200173, the initial compliance time for doing the tasks specified in paragraph 4 of EASA AD 20200173 is at the applicable associated thresholds specified in paragraph 4 of EASA AD 2020
0173, or within 90 days after the effective date of this AD, whichever occurs later.
5 Where table 1 of EASA AD 20200173
specifies a compliance time of without exceeding the previous threshold and interval as specified in TLD Time Limits Document Revision 16 for this AD use without exceeding the compliance times specified in paragraph g of this AD.
6 The provisions specified in paragraphs 5 and 6 of EASA AD 20200173 do not apply to this AD.
7 The Remarks section of EASA AD
20200173 does not apply to this AD.
1 Alternative Methods of Compliance AMOCs: The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch, send it to the attention of the person identified in paragraph o of this AD.
Information may be emailed to: 9-AVS-AIR730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.
2 Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or ATRGIE Avions de Transport Regionals EASA Design Organization Approval DOA. If approved by the DOA, the approval must include the DOAauthorized signature.
m New Provisions for Alternative Actions and Intervals After the maintenance or inspection program has been revised as required by paragraph k of this AD, no alternative actions e.g., inspections or intervals, are allowed unless they are approved as specified in the provisions of the Ref.
Publications section of EASA AD 2020
0173.
n Other FAA AD Provisions The following provisions also apply to this AD:
PO 00000
Frm 00015
Fmt 4700
Sfmt 4700
o Related Information For more information about this AD, contact Shahram Daneshmandi, Aerospace Engineer, Large Aircraft Section, International Validation Branch, FAA, 2200
South 216th St., Des Moines, WA 98198;
telephone and fax 2062313220; email shahram.daneshmandi@faa.gov.
E:FRFM24FER1.SGM
24FER1
ER24FE21.004 ER24FE21.005
Federal Register / Vol. 86, No. 35 / Wednesday, February 24, 2021 / Rules and Regulations
