Voglio sapere a riguardo di…

Federal Register / Vol. 86, No. 19 / Monday, February 1, 2021 / Notices 8 X 20
Style: 4 X 4 W4/W4 or D4/D4 i.e., 4 gauge Sheet Size:
5 X 10
8 X 126
8 X 128
8 X 15
8 X 20
Any product imported, sold, or invoiced in one of these size combinations is within the scope.

ASTM specification A1064/A1064M
provides for permissible variations in wire gauges, the spacing between transverse and longitudinal wires, and the length and width combinations. To the extent a roll or sheet of welded wire mesh falls within these permissible variations, it is within this scope.
ASTM specification A1064/A1064M also defines permissible oversteeling, which is the use of a heavier gauge wire with a larger cross-sectional area than nominally specified.

1.4
2.1
2.9
4.0

i.e., i.e., i.e., i.e.,
10 gauge
8 gauge
6 gauge
4 gauge

3.4
4.1
4.9
6.0

Diameter range inch 0.093
0.161
0.189
0.223

to to to to
0.211.
0.231.
0.253.
0.280.

To the extent a roll or sheet of welded wire mesh falls within the permissible variations provided above, it is within this scope.
In addition to the tolerances permitted in ASTM specification A1064/A1064M, wire mesh within this scope includes combinations where:
1. A width and/or length combination varies by one grid size in any direction, i.e., 6 inches in length or width where the wire meshs grid size is 6 X 6; and/or 2. The center-to-center spacing between individual wires may vary by up to one quarter of an inch from the nominal grid size specified.
Length is measured from the ends of any wire and width is measured between the center-line of end longitudinal wires.
Additionally, although the subject wire mesh typically meets ASTM A1064/A1064M, the failure to include certifications, test reports or other documentation establishing that the product meets this specification does not remove the product from the scope. Wire mesh made to comparable foreign specifications e.g., DIN, JIS, etc. or proprietary specifications is included in the scope.
Excluded from the scope is wire mesh that is galvanized i.e., coated with zinc or coated with an epoxy coating. In order to be excluded as galvanized, the excluded welded wire mesh must have a zinc coating thickness meeting the requirements of ASTM
specification A641/A641M. Epoxy coating is a mix of epoxy resin and hardener that can be applied to the surface of steel wire.
Merchandise subject to this investigation are classified under Harmonized Tariff Schedule of the United States HTSUS
categories 7314.20.0000 and 7314.39.0000.
While HTSUS subheadings are provided for convenience and customs purposes, the written description of the scope of this investigation is dispositive.

V. Scope of the Investigation VI. Application of Facts Available, Use of Adverse Inferenes, and Calculation of All-Others Rate VII. Discussion of the Methodology A. Determination of the Comparison Method B. Results of the Differential Pricing Analysis VIII. Date of Sale IX. Product Comparisons X. Constructed Export Price XI. Normal Value A. Home Market Viability B. Affiliated-Party Transactions and Arms Length Test C. Level of Trade D. Cost of Production COP Analysis 1. Calculation of COP
2. Test of Comparison Market Sales Prices 3. Results of the COP Test XII. Currency Conversion XIII. Recommendation
Appendix IIList of Topics Discussed in the Preliminary Decision Memorandum
The Department of Commerce will submit the following information collection request to the Office of Management and Budget OMB for review and clearance in accordance with the Paperwork Reduction Act of 1995, on or after the date of publication
I. Summary II. Background III. Period of Investigation IV. Scope Comments
VerDate Sep<11>2014

16:57 Jan 29, 2021

Jkt 253001

It also permits a wire diameter tolerance of 0.003 inches for products up to W5/D5 and 0.004 for sizes over W5/D5. A producer may oversteel by increasing smooth or deformed wire diameter up to two whole number size increments on Table 1 of A1064.
Subject wire mesh has the following actual wire diameter ranges, which account for both oversteeling and diameter tolerance:

Maximum oversteeling No.

W/D No.

FR Doc. 202102079 Filed 12921; 8:45 am BILLING CODE 3510DSP

DEPARTMENT OF COMMERCE
National Oceanic and Atmospheric Administration Agency Information Collection Activities; Submission to the Office of Management and Budget OMB for Review and Approval; Comment Request; Sea Grant Program Application Requirements for Grants, for Sea Grant Fellowships, Including the Dean John A. Knauss Marine Policy Fellowships, and for Designation as a Sea Grant College or Sea Grant Institution
PO 00000

Frm 00026

Fmt 4703

Sfmt 4703

7713

of this notice. We invite the general public and other Federal agencies to comment on proposed, and continuing information collections, which helps us assess the impact of our information collection requirements and minimize the publics reporting burden. Public comments were previously requested via the Federal Register on October 28, 2020, during a 60-day comment period.
This notice allows for an additional 30
days for public comments.
Agency: National Oceanic &
Atmospheric Administration, Commerce.
Title: Sea Grant Program Application Requirements for Grants, for Sea Grant Fellowships, including the Dean John A.
Knauss Marine Policy Fellowships, and for Designation as a Sea Grant College or Sea Grant Institution.
OMB Control Number: 06480362.
Form Numbers: NOAA Forms 901;
902; 904.
Type of Request: Regular submission.
Revision and extension of a current information collection.
Number of Respondents: 114.
Average Hours per Response: Form 90130 minutes; Form 902 Excel 20 minutes, Webform15 minutes;
Form 90415 minutes; Application for Designation as a Sea Grant College or Regional Consortia20 hours;
Application for Sea Grant Fellowship 2 hours.
Total Annual Burden Hours: 783.
Needs and Uses: This request is for the extension, with minor proposed revisions, of a currently approved information collection. The objectives of the National Sea Grant College Program, as stated in the Sea Grant legislation 33
U.S.C. 1121 et seq. are to increase the understanding, assessments, development, utilization, and conservation of the Nations ocean, coastal, and Great Lakes resources. It accomplishes these objectives by
E:FRFM01FEN1.SGM

01FEN1