Voglio sapere a riguardo di…

48

Federal Register / Vol. 86, No. 1 / Monday, January 4, 2021 / Proposed Rules
SUPPLEMENTARY INFORMATION:

Section 31501b of the Moving Ahead for Progress in the 21st Century Act MAP
21 requires the Secretary NHTSA, by delegation to commence and complete a rulemaking to amend the standard seat assembly in FMVSS No. 213 to better simulate a single representative motor vehicle rear seat. Pursuant to this mandate, on November 2, 2020, NHTSA
published an NPRM proposing to amend FMVSS No. 213 by updating the standard seat assembly NHTSA uses to test child restraint systems CRSs for compliance with the standards dynamic performance requirements.
This NPRM proposed other amendments to modernize FMVSS No.
213, including ways to streamline the Agencys use of test dummies to assess restraint performance. NHTSA provided a 60-day comment period for the November 2, 2020 proposal, which closes on January 4, 2021.

extensive, and evaluation of the changes requires the fabrication of standard seat assemblies, which JPMA said would take 8 to 16 weeks for delivery to the testing facilities. JPMA stated that without the ability to inspect, fully evaluate and conduct comparative testing using this new bench, particularly in regard to its repeatability and reproducibility characteristics, our CRS manufacturing members are seriously limited in their ability to comment in the time period prescribed in the current NPRM.
On December 11, 2020, the Childrens Hospital of Philadelphia CHOP
submitted a petition to extend the comment period. CHOP did not specify the additional time sought but argued that remote teleworking and competing work due to the public health emergency has created challenges to gather all the individuals and relevant data to draft a response.

Petitions
Agency Decision In accordance with NHTSAs rulemaking procedures in 49 CFR part 553, subpart B, the Agency is granting the petitioners requests to extend the comment period, but is extending it only for 90 days. NHTSA has determined that the petitioners have shown good cause for an extension, and that the extension is consistent with the public interest 49 CFR 553.19. Entities seeking to build the proposed standard seat assembly need time to procure materials and fabricate the assembly.
NHTSA typically procures test seat assemblies in 6 to 8 weeks, but understand that it may take longer to obtain the seat assembly discussed in the NPRM due to possible customer demand, the time needed to procure the seat foam 812 weeks, and the business restrictions caused by the public health emergency. However, JPMA has not provided any basis explaining why it would take 8 to 16
weeks, almost twice the normal time, to procure the assembly. Without a reasoned explanation for the exceptionally long period, we conclude a 120-day extension is unwarranted and unduly delays the rulemaking.
In considering the petitions, NHTSA
weighed the statutory interest in completing this rulemaking, the
The Juvenile Products Manufacturers Association JPMA, representing manufacturers of child restraint systems, submitted a petition on December 14, 2020 requesting a 120-day extension of the comment period for the November 2, 2020 NPRM.1 JPMA
provided several reasons for extending the comment period, including the need for social distancing and restrictions on businesses due to the public health emergency, the delay in public release of the drawing package for the standard seat assembly referenced by the NPRM, and the plans of some manufacturers to evaluate the proposed standard seat assembly by fabricating and evaluating the assembly for repeatability and reproducibility of results with the child restraint models they produce. JPMA
stated that the original 60-day comment period does not adequately reflect the time necessary for manufacturers to evaluate the potential implications of the NPRM thoroughly and to provide constructive feedback to NHTSA. They argued that the proposed changes are 1 JPMA requested that the comment period be extended to 180 days from the date of publication of the NPRM. NHTSA understands this request to include the 60 days provided by the NPRM, which means JPMA is requesting a 120-day extension.

VerDate Sep<11>2014

17:03 Dec 31, 2020

Jkt 253001

PO 00000

Frm 00020

Fmt 4702

Sfmt 9990

complexity and importance of the rulemaking, and the basis for the requests. The 3-dimensional drawings of the standard seat assembly were made public on November 16, 2020.2 Based on an 8 to 12-week lead time for fabrication and delivery of the proposed seat assembly, NHTSA estimates entities could acquire the proposed seat assembly for evaluation between midJanuary and early February 2021. A 90day extension of the comment period provides sufficient time following procurement of the seat assembly for interested persons to test CRSs, analyze results, and prepare comments.
Therefore, NHTSA partially grants the requests for extending the comment period by extending it for 90 days.
The Agency supports efforts to develop useful technical information on the proposal and believes 90 additional days will achieve that result. Extending the comment period 90 days balances the need to provide more time to entities to assess the proposal with the need to incorporate a representative vehicle seat in FMVSS No. 213
compliance tests expeditiously.
Incorporating a representative vehicle seat in FMVSS No. 213 will provide a more meaningful assessment of the performance of CRSs in vehicles on the road today.
Please note that even after the comment closing date has passed, interested persons are able to file comments in the docket, which NHTSA
will consider to the extent practicable.
49 CFR 553.23. NHTSA may also continue to file relevant information in the docket as it becomes available.
Accordingly, the Agency recommends that readers periodically check the docket for new material.
Authority: 49 U.S.C. 322, 30111, 30115, 30117, and 30166; delegation of authority at 49 CFR 1.95 and 49 CFR 501.8.
Issued in Washington, DC, under authority delegated in 49 CFR 1.95 and 501.8.
James C. Owens, Deputy Administrator.
FR Doc. 202029111 Filed 123020; 11:15 am BILLING CODE 491059P
2 JPMA incorrectly stated the publishing date was November 9, 2020.

E:FRFM04JAP1.SGM

04JAP1