Quiero saber acerca de...

Federal Register / Vol. 86, No. 158 / Thursday, August 19, 2021 / Proposed Rules a Comments Due Date The FAA must receive comments on this airworthiness directive AD by October 4, 2021.
b Affected ADs None.
c Applicability This AD applies to Dassault Aviation airplanes identified in paragraphs c1
through 3 of this AD, certificated in any category, as identified in European Union Aviation Safety Agency EASA AD 2021
0047, dated February 16, 2021 EASA AD
20210047.
1 Model FALCON 7X airplanes.
2 Model FALCON 900EX airplanes.
3 Model FALCON 2000EX airplanes.
d Subject Air Transport Association ATA of America Code 51, Standard Practices/
Structures.

k Related Information
e Reason This AD was prompted by a report of an improper heat treatment process applied during the manufacturing of certain Decomatic titanium screws. The FAA is issuing this AD to address failure of an affected screw installed in a critical location, possibly resulting in reduced structural integrity of the airplane.
f Compliance Comply with this AD within the compliance times specified, unless already done.
g Requirements Except as specified in paragraph h of this AD: Comply with all required actions and compliance times specified in, and in accordance with, EASA AD 20210047.
h Exceptions to EASA AD 20210047
1 Where EASA AD 20210047 refers to its effective date, this AD requires using the effective date of this AD.
2 The Remarks section of EASA AD
20210047 does not apply to this AD.
3 Where EASA AD 20210047 specifies to replace each serviceable part, for this AD that replacement includes an inspection of the bore dimension and corrective actions oversizing or repair, as specified in the service information referenced in EASA AD
20210047.

lotter on DSK11XQN23PROD with PROPOSALS1

i No Reporting Requirement Although the service information referenced in EASA AD 20210047 specifies to submit certain information to the manufacturer, this AD does not include that requirement.
j Other FAA AD Provisions The following provisions also apply to this AD:
1 Alternative Methods of Compliance AMOCs: The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your
VerDate Sep<11>2014

16:45 Aug 18, 2021

Jkt 253001

principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch, send it to the attention of the person identified in paragraph k2 of this AD.
Information may be emailed to: 9-AVS-AIR730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office.
2 Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Dassault Aviations EASA Design Organization Approval DOA. If approved by the DOA, the approval must include the DOA-authorized signature.
1 For information about EASA AD 2021
0047 contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49
221 8999 000; email ADs@easa.europa.eu;
Internet www.easa.europa.eu. You may find this EASA AD on the EASA website at https ad.easa.europa.eu. You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200
South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 2062313195. This material may be found in the AD docket on the internet at https www.regulations.gov by searching for and locating Docket No.
FAA20210684.
2 For more information about this AD, contact Tom Rodriguez, Aerospace Engineer, Large Aircraft Section, International Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 2062313226; email tom.rodriguez@
faa.gov.
Issued on August 12, 2021.
Lance T. Gant, Director, Compliance & Airworthiness Division, Aircraft Certification Service.
FR Doc. 202117677 Filed 81821; 8:45 am BILLING CODE 491013P

DEPARTMENT OF THE TREASURY
Fiscal Service 31 CFR Part 210
RIN 1530AA26

Federal Government Participation in the Automated Clearing House Fiscal Service, Bureau of the Fiscal Service, Treasury.
ACTION: Notice of proposed rulemaking with request for comment.
AGENCY:

SUMMARY: The Department of the Treasury, Bureau of the Fiscal Service Fiscal Service is proposing to amend
PO 00000

Frm 00026

Fmt 4702

Sfmt 4702

46631

its regulation governing the use of the Automated Clearing House ACH
Network by Federal agencies. Our regulation adopts, with some exceptions, the Operating Rules Operating Guidelines Operating Rules & Guidelines developed by Nacha as the rules governing the use of the ACH
Network by Federal agencies. We are issuing this proposed rule to address changes that Nacha has made since the publication of the 2019 Operating Rules & Guidelines. These changes include amendments set forth in the 2020 and 2021 Operating Rules & Guidelines, including supplements thereto, issued on or before March 31, 2021.
DATES: Comments on the proposed rule must be received by October 18, 2021.
ADDRESSES: Comments on this rule, identified by docket FISCAL2021
0002, should only be submitted using the following methods:
Federal eRulemaking Portal:
www.regulations.gov. Follow the instructions on the website for submitting comments.
Mail: Ian Macoy, Bureau of the Fiscal Service, 3201 Pennsy Drive, Building E, Landover, MD 20785.
The fax and email methods of submitting comments on rules to Fiscal Service have been decommissioned.
Instructions: All submissions received must include the agency name Bureau of the Fiscal Service and docket number FISCAL20210002 for this rulemaking. In general, comments received will be published on Regulations.gov without change, including any business or personal information provided. Comments received, including attachments and other supporting materials, are part of the public record and subject to public disclosure. Do not disclose any information in your comment or supporting materials that you consider confidential or inappropriate for public disclosure. You can download this proposed rule at the following website:
https www.fiscal.treasury.gov/ach/.
In accordance with the U.S.
governments eRulemaking Initiative, Fiscal Service publishes rulemaking information on www.regulations.gov.
Regulations.gov offers the public the ability to comment on, search, and view publicly available rulemaking materials, including comments received on rules.
FOR FURTHER INFORMATION CONTACT: Ian Macoy, Director of Settlement Services, at 202 8746835 or ian.macoy@
fiscal.treasury.gov; or Frank J. Supik, Senior Counsel, at frank.supik@
fiscal.treasury.gov.
SUPPLEMENTARY INFORMATION:

E:FRFM19AUP1.SGM

19AUP1