Quiero saber acerca de...

Federal Register / Vol. 86, No. 146 / Tuesday, August 3, 2021 / Proposed Rules
41797

Figure 1 to the introductory text of paragraph g - Affected MLG Drag Strut
Assembly Part Number
Serial N um her MBM0056
MBM0073
MBM0076
MBM0130
MBM0136
MBM0145
MBM0179
MBM0204
MBM0208

46301-13

MBM0302
MBM0303
MBM0324
MBM0405
MBM0408
MBM0412
MBM0417
MBM0423

1 Within 80 flight hours after accomplishing the records review required by paragraph g of this AD, do a detailed inspection for cracking of the affected MLG
drag strut assembly, and do all applicable oncondition actions before further flight, in accordance with a method approved by the Manager, New York ACO Branch, FAA.
Repeat the inspection thereafter at intervals not to exceed 80 flight hours until the magnetic particle inspection required by paragraph g2 of this AD is done.
Note 1 to paragraph g1: Guidance on the inspections and on-condition actions required by this AD can be found in Transport Canada Civil Aviation TCCA AD
CF202043, dated October 21, 2020.
2 Within 1,600 flight hours or 12 months after the effective date of this AD, whichever occurs first, perform a magnetic particle inspection for cracks of the entire tubular section of the affected MLG drag strut assembly, and do all on-condition actions before further flight, in accordance with a method approved by the Manager, New York ACO Branch, FAA. Performing the magnetic particle inspection required by this paragraph terminates the repetitive detailed inspections required by paragraph g1 of this AD.

VerDate Sep<11>2014

16:59 Aug 02, 2021

Jkt 253001

h Parts Installation Prohibition As of the effective date of this AD, no person may install an affected MLG drag strut assembly identified in figure 1 to the introductory text of paragraph g of this AD
on any airplane unless the inspections and applicable on-conditions specified in paragraphs g1 and 2 of this AD are done before further flight.
i Other FAA AD Provisions The following provisions also apply to this AD:
1 Alternative Methods of Compliance AMOCs: The Manager, New York ACO
Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the certification office, send it to ATTN: Program Manager, Continuing Operational Safety, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 5162287300; fax 5167945531. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a
PO 00000

Frm 00039

Fmt 4702

Sfmt 4702

principal inspector, the manager of the responsible Flight Standards Office.
2 Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, New York ACO Branch, FAA; or Transport Canada Civil Aviation TCCA; or De Havilland Aircraft of Canada Limiteds TCCA Design Approval Organization DAO. If approved by the DAO, the approval must include the DAOauthorized signature.
j Related Information 1 Refer to Mandatory Continuing Airworthiness Information MCAI TCCA AD
CF202043, dated October 21, 2020, for related information. This MCAI may be found in the AD docket on the internet at https www.regulations.gov by searching for and locating Docket No. FAA20210613.
2 For more information about this AD, contact Aziz Ahmed, Aerospace Engineer, Airframe and Propulsion Section, FAA, New York ACO Branch, 1600 Stewart Avenue, Suite 410, Westbury, NY 11590; telephone 5162287329; fax 5167945531; email 9avs-nyaco-cos@faa.gov.
3 For information about TCCA AD CF
202043, dated October 21, 2020, contact
E:FRFM03AUP1.SGM

03AUP1

EP03AU21.001

jbell on DSKJLSW7X2PROD with PROPOSALS

BILLING CODE 491013C